IT'S MY TURN NOW!!!

ACTIVITY ON 12/5/10

for the first time i had a chance to do all this...thanks to En. saiedin n Khairool for giving me a chance to experience this...this week cable lab kind of hectic because two test ongoing at the same time...furthermore not many technician available at the lab because this week got one team of PD testing need to go to Pasir Gudang for a week..since the staff not enough, so this is the right time for me as practical student to help them and gain experiences...

what am i doing???

take the temperature reading

inject/drop the current (0 - 420A)

ACTIVITY ON 11/5/10

last few week, i attended a course bout all the testing procedure...one of the topic was how to measure contact resistance (CR)...so today, en. Saeidin ask me to do all the procedure required...

connecting the sensor with the CR

set the inject current (60A) - this tool quite heavy =D

waiting for the reading

print out the result

evaluate the CR base on the result

TNBR MONTHLY INTELLECTUAL DISCOURSE

ACTIVITY ON 10/5/10

TITLE :

PILOT CABLE FAULT DETECTION USING TIME DOMAIN REFLECTROMETRY METHOD

PRESENTER :

MOHD. RUZLIN B. MOHD. MOKHTAR

DEPARTMENT :

CABLE DIAGNOSTIC

What is PILOT CABLE ??

- is a supervisory communication pilot cable

- laid underground side by side with the underground power cable

- have been used in TNBR for :

> unit protection scheme

> communication channel for telecontrol

> SCADA Purposes

PILOT Cable construction

Two types of pilot cable used in distribution system :

- 12 pairs & 37 pairs for 11kV system

- 37 pairs for 33kV system

Fault Locating Method :

(a) Conventional Method : personalizing and thumping

(b) New method : Time Domain Reflectrometry (TDR)

Pilot cable Fault Types :

- open circuit

- short circuit

- splice/joint

- wet splice

- high resistance splice

- transceiver

- tap / lateral

- water ingress

- split and resplit

- cross

FIRST SITE VISIT @ PULAU BANDING

ACTIVITY ON 25/4/10

* i forgot to publish this entry...this should be before the Pulau Banding 1...sorry for the inconvenience....

going for a site visit with authorise person form TNBD Ipoh, foreman Shamsul and En. Faris...

went to the site before take any further action...the location is base on the report provided by TNBD Ipoh... ( Location : BS-BG 76)



*Thermography Analysis*

according to contractor, base on their inspection..they found hot spot at overhead line...how they capture the hot spot??? picture above, somthing like camera hold by En. Faris was used to determine the hot spot location... however, hot spot cannot be seen (not really clear) on bright day...

this is the location of hot spot...they did the analysis at night...the joint was on a tray at the pole

this is the scanned picture...above this was the original firgure and this is the result they get and evaluate the level of hot sopt base on the temperature...different location will have different temperatute...as u can see in the picture...the 20 degree C was the references temperature at that surrounding..if there is a spot with temperature high than its references temperature, they will clarify it as hot spot...

short discussion with the boss about what we should do when we come back later....

discussion with foreman Shamsul n En. Faris on how and where to install the energy logger... our first choice to install is at termination.. but since at termination required a shutdowm, it give us a bit problem in order for us to do our job tomorrow..to arrange a shutdown TNB need at least a week to arrange it..they need to give a notice to residences, premise, resort and etc to inform them about the shutdown... if fail to do so, after 10min (usually) of shutdown, TNB will recieve a lots of phone call... =D

Pulau Banding II

ACTIVITY ON 7/5/10 - 8/5/10



This is my 3rd time at Pulau Banding....this time, the purpose still the same..install the same equipment...measure the same thing...expect to have the pattern of current as theory...the only different from previous, this time we install at termination...



why we dont install at termination before???



oraite...like this...we all experienced the blackout nite...sleep without fan/air-con...for sure u will mad because no electricity all of sudden...so that, in order to avoid customer unsatisfied..we should give them a notice in order to do the shutdown.....



at termination..we need to shutdown fisrt before we can touch the joint...if there is still voltage up there n u touch it...in few second u will 'goal'....so that shutdown is the solution to avoid any death....


how to check whether the voltage/current zero or not???

as u can see...there is a rod hanging up there...the yellow rod is known as discharge rod....the rod can ensure all the voltage/current have been discharge complete or not...and after that we can touch the termination safely...

complete installation at termination

checking the load for tonight....to check whether it's balance or not...reading taken at SSU Bersia

comparing the result between TNBD Ipoh' s 'tong' with TNBR's 'tong'

* tong is the name of the device that display the reading above

this is the source center that supply current all the way from Bersia to Banding

CBM course

ACTIVITY ON : 4/5/10 - 6/5/10

CBM Course @ TNB Intergrated Learning Solution Sdn. Bhd. (ILSAS)

lecture class

course manual

course participant

En. Razlan give some explainsion about STRESS TEST

En. Khairul explain about Insulation Resistance (IR) using Meggar

IR Measurement

Partial Discharge set up (PD Testing)

Listen to the explainasion about PD testing

En. Razlan show us how to use TDR - Time Domain Reflectometry

week 4 : Pulau banding I

ACTIVITY ON 26/4/10 - 30/4/10

last sunday, we had a site visit... actually the actual date for us to do the installation is on week 5 but since there is certain reason we need to bring forward the date...

DAY 1 : 26/4/10 (travelling day)

DAY 2 : 27/4/10

9.30 - breakfast

10.00 - drive to the site (pole 102, 90, 88)

10.40 - reset Current Transformer / energy logger (at site)

11.15 - install energy logger at straight trough joint (on the tray at the top of pole)

complete installation for the 1st day

Reset the energy logger - before we install it at the overhead line, the setting of the equipment should be done manually. the data logger will be leave at the top of pole for the straight 12 hours.

" ku sangka panas sampai ke petang , rupanya hujan di tongah hari ".... after the rain has stopped, we plan to continue the job but the above incident happened when ' uncle .... ' try to adjust the crane hogger and put it at the right position. well, nothing we can do unless wait for the help of another crane to pull i out. after an hour then we can proceed the job.

those two pictures above are taken during the installation process..according to En. Saeidin, this work are done 7m from the land. the person who is responsible to do this must know the theory behind it as well, its not simply go up there and plug in the device. ie; the person should now the basic idea about eletcric. however, this activity was supervised by the TNBR's foreman from cable unit.

DAY 3 : 28/4/10

Day by day, new thing pop up...for today after uninstall the energy logger, we have to transfer the collected data into the software in order for us to see the patern of current flow during peak hour and ordinary hour.

the lady in blue jacket was my sub-supevisor...she was one of the engineer in High Voltage Diagnostic unit...at this moment we all quite stress when the data we get not as what we expected...discussion still ongoing eventhough we sat next to the main road...

"Poning Eden ngan data nie" <<< en. saeidin ^_^

dangerous just next to me... " malang tak berbau "...

communicate with teamate up there...

TNBR joinventure with TNBD Kuala Kangsar

Praise to God... we have a good coorperation with them in order for us to use the crane hogger...wothout their help, for sure we cannot reach the top pole

This is a straight through joint...view from top

the cable on the tray was the joint cable and the energy logger was installed here..

WRONG!!!!

the cable shoudn't be hang up just like that...every single joint MUST place on the tray

CORRECT!!!

its me!!!.. i was given an opportunity to experience it... ^_^

the diagram shown the route from SSU Bersia to PPU Tasik Banding

the red dot indicates very seroius condition..if late action, it will explode.

DAY 4 : 29/4/10

same like yesterday and the day before... set up the energy logger

installation work

" walaupon gayat...he willing to go up there...tanggungjawab bertugas kan... =p "

this not facbooking k...this is double checking eventhough evrything was set up just now

DAY 5 : 30 /4/10

9.30 - breakfast

10.55 - uninstall the energy logger

11.30 - travelling back to TNBR

5.30 - arrive at TNBR

NEW EQUIPMENT

ACTIVITY ON 21/4/10

EQUIPMENT 1 : ENERGY LOGGER

this equipment has 3 functions :

1) to measure temperature

2) to measure current

3) to measure solar radiation

Setup Energy Logger by the seller

in yellow circle is Current Transformer
(on site)

EQUIPMENT 2 : DIELECTRIC SPECTROSCOPY TESTING

in yellow circle is High Voltage Unit

there are two common types of cable that have been use for UG cable which are PILC and XLPE... since the type already different, therefore the way to handle DS test also different..

what differentiate them is just ' High Voltage Unit '.... for XLPE cable, it require HVU in order for us to see the dependent voltage..as i explained before, water tree can only occur in XLPE cable...therefore the dependent voltage will help in determining the existence of water tree...

Result Comfirmation